Looking for:
Tesla wall charger installation manual |
Tesla wall charger installation manual.Installing your Tesla Home Charger (Gen. 2)
Clamp Connector. The cord comes with with ring terminal connectors and an adjustable strain relief bracket. Using a screwdriver, loosen the strain relief bracket and slide it off the cable.
This bracket is not needed and can be disgarded. The NEMA plug has four conductors two hots, neutral, and ground , but only three are required for this installation.
Cut the ring connectors off of the red hot , black hot , and green ground cables. Cut the white neutral cable down to the sheath. This can be observed in the next step. Wrap where the wires meet the sheath with some electrical tape to keep the installation clean and ensure the neutral wire is not exposed.
In order to install the cord, you must open up the Wall Connector. This will expose the case cover. Remove the T20 security Torx screws with the supplied bit that came with the Wall Connector. Remove the case cover and the cord connection terminals will now be accessible. Loosen all three terminals L1, L2, and Ground. Refer to the picture for location notes,. The conduit connector on the bottom of the Wall Connector is treaded allowing the 1-inch twin-screw clamp connector to screw into place.
Remove the nut on the threaded portion of the clamp connector and snuggly screw the connector into place on the bottom of the Wall Connector. This step is not pictured. With the screw connector in place and the twin-screw clamp loosened, feed the cord through the clamp connector and into the Wall Connector unit.
Feed the red wire into the L1 terminal, the black wire into the L2 terminal, and the green wire into the Ground terminal. With each wire in place, tight down the associated terminal. Now tighten down the twin-screw clamp on the cord.
Two switches must be set in order for the Wall Connector to operate properly. First, switch 1 of the dip switch, must be set to the down or off position line-to-line.
Second, the rotary switch must be set to position 8 40A charging. Tesla offers the best in EV technology, and you should have matching high-tech charging equipment so that you can confidently plug in your Tesla and add power to it safely.
By having your Tesla charger installed at your home, you can simply connect your Tesla to the wall charger when you go to sleep and get your fully charged Tesla ready for action in the morning. Our team of expert Tesla wall charger installation electricians can take care of every aspect of your charger installation at a minimal cost.
When you are in need of any commercial or residential Electrician, let us at NZM Electrical Services assist you with all your electrical needs. We offer all type of electrical services at competitive prices. Highly Recommended! Had the team install a Gen 3 Tesla charger at the premises. Affordable quote and professional install.
Great work and would recommend these guys to anyone looking for a EV charger install in Sydney! Absolutely fantastic business to work with. Used if you end up not using the entry holes. Bottom or rear entry signal conduit plug. Top entry signal conduit plug. Top entry power conduit plug. Bottom conduit sealing gasket.
This is recommended if you are installing outdoors. Top bracket-to-housing screw covers. Bottom bracket-to-housing screw covers. Bottom bracket-to-housing screws. Top entry bracket mounting screws. For my Model 3, I set it at number 9 so I can get 60 amps. Figure out whether you want to do a rear, bottom, or top entry. Keep in mind that the further away from the breaker box, the more expensive the job will be.
Note: Consult with your local electrician or refer to your local code for proper wire sizing appropriate for the currents in your Wall Connector. Note: It is the installer's responsibility to identify whether additional grounding is required to ensure that local regulations are met.
Grounding must be installed at the power source and not at the cable entry to the Wall Connector. Note: For three-phase wiring, connect the terminal block with the L1, L2, L3, neutral, and ground. Warning: Do not connect service wiring until you have read and fully understand the concepts described in Service Wiring The following illustration shows an on page 7.
Turn off the power. For top entry installation, pull the service 3. Strip the service wires going to the wiring into the top entry bracket or the terminal block on the top entry bracket 8 Wall Connector.
Use an M32 cable gland mm. Ferrules are recommended. Note: For top entry installation, the Note: The meaning of wiring colors might flexible pre-installed wires that go from vary from country to country. Follow all the top entry bracket to the housing are applicable national and local regulations already terminated and do not need to be concerning wiring color codes. Lead the preconnected service wires in the main housing and connect the preconnected service wires to the main terminal block cross section: 10 mm, diameter: 3.
Caution: Cut each of the wire strands and insert them fully into each the terminal block. Note: To ensure proper operation, verify that neutral is connected to the neutral line inside the circuit breaker box or the main electrical panel. Check for miswiring using a multimeter and verify that there are no shorts before turning the upstream circuit breaker ON. The following illustration shows an enlarged view of the DIP and rotary switches.
Changing these switches with TT-TN the power ON will not be recognized by the system and is dangerous due to the risk of electric shock. Turn OFF power. Set the rotary switch for the appropriate Warning: Before you set the DIP current setting supported by your circuit switches, confirm which type of breaker. Typical circuit breaker ratings are: input service the utility provides.
The corresponding rotary switch settings for the typical circuit breakers are shown in the following table:. Use a T20 security pin Torx driver to 0 Test mode install the remaining screws on the sealing cover.
Ensure that the cover is properly 1 6A aligned before fully tightening the screws. Attach the outer cover to the sealing 2 8A cover starting with the latch at the top. Engage the snaps on the sides and align 3 10A the mounting tab with the housing at the 4 13A bottom. E Not a valid selection 3.
Use a T10 Torx driver to install the screw F Slave mode that secures the bottom of the outer cover 4. Reattach the ribbon cable to the sealing to the housing. Close any unused openings with power 5. Reinstall the sealing cover. Use a T20 and signal conduit plugs. Connector, and the Wall Connector should 6. Turn ON power. If the installation is successful, the LEDs environment. Turn ON the power. If there is a solid on page 21 and resolve the error before or flashing Red LED, resolve the error you continue.
Write the contact information of the 6. Attempt to charge the vehicle to ensure installer on the label on the inside of the the Wall Connector is operating correctly Wall Connector. For instructions on how to charge, refer to the owner information provided with the vehicle. Top light Off Off Not Power on. The Wall Not applicable. Streaming 1 flash Off Not Charging current is Make sure the lights applicable reduced due to high connector is fully temperature inserted into the detected in the charge inlet in the Vehicle Connector.
Streaming 2 flashes Off Not Charging current is If the Wall Conector is lights applicable reduced due to high plugged into a wall temperature outlet, make sure that detected in the wall it is fully inserted into plug or on the input the receptacle, it is terminals to the not covered by Wall Connector. If the Wall Connector is hard-wired, make sure it is not covered by anything, andthere is no heat source nearby. Streaming 3 flashes Off Not Charging current is Make sure the Wall lights applicable reduced due to high Connector is not temperature covered by anything detected inside the and there is no heat Wall Connector.
Off Off 1 flash After 15 Ground Try again by minutes and fault. Current is disconnecting the up to 4 leaking through an Wall Connector from times unsafe path. If the ground or Neutral problem persists, turn to ground fault.
OFF the circuit breaker servicing the Wall Connector, wait 10 seconds, turn the circuit breaker ON again, then try reconnecting the Wall Connector to the vehicle. If the problem persists, contact Tesla. Off Off 2 flashes After 1 No ground Make sure the Wall minute and connection Connector is properly up to 4 detected in the Wall grounded. If uncertain, times Connector. Consult your electrician.
Off Off 4 flashes After 1 Over or under Consult your minute and voltage protection. Off Off 5 flashes After 1 Over current Reduce the vehicle's minute retry protection. If the problem retries persists and the attached vehicle is manufactured by Tesla, contact Tesla.
If the problem persists and If the attached vehicle is not manufactured by Tesla, contact the original manufacturer. Off Off 6 flashes After 1 A communication If possible, plug the minute retry error occurred vehicle into another no limit on between the Wall Wall Connector or a retries Connector and the Mobile Connector to vehicle.
Then contact Tesla Service. Top light Off 1 flash No Over temperature Make sure the Wall on protection latch- Connector, vehicle off connectors, and wall plug if used are not covered by anything and there is no heat source nearby.
Top light Off 2 flashes No Non-Tesla vehicle Compatible input on attempting distributions are: connection to non- single-phase compatible input distribution or V, distribution.
Top light Off 3 flashes No Incorrect rotary Consult your on switch setting. All Master. Set one of the Wall Connectors to Slave. Circuit Breaker Sharing Network.
This clears the fault message but does not reboot the Wall Connector. If the light returns to flashing RED, the fault state has not been corrected. Caution: Do not allow the sealing cover to hang from the ribbon cable. Doing so can damage the ribbon Before continuing, use a voltmeter to cable or its connectors.
Reposition the rotary switch to the service wiring or terminals. Use a non-conductive object to adjust the DIP switches to the appropriate grid Reattach the ribbon cable to the sealing setting and circuit breaker sharing setting cover. Replace all the screws and reinstall the page Use a small flathead screwdriver to set the Power Up on page
❿
No comments:
Post a Comment